Sized for front or rear for the correct retro-fit into your existing instrument, these impressive pickups give you the full spectrum of sounds you would expect from a high quality bass guitar. Full toned, with crisp and clear note detail.

Read more less

Jerry Donahue's exacting specifications these single coil pickups off unparalleled tone and versatility. With Alnico V magnets, staggered pole pieces and custom wound to Jerry Donahue's exacting specifications these single coil pickups off unparralled tone and versatility.

Read more less

Jerry Donahue's exacting specifications these single coil pickups off unparalleled tone and versatility. With Alnico V magnets, staggered pole pieces and custom wound to Jerry Donahue's exacting specifications these single coil pickups off unparralled tone and versatility.

Read more less

Custom wound to an authentic vintage voiced recipe, these Wilkinson hot-output 'JV' single coil pickups feature staggered poles with chamfered Alnico V magnets.

Read more less

Custom wound to an authentic vintage voiced recipe, these Wilkinson hot-output 'JV' single coil pickups feature staggered poles with chamfered Alnico V magnets.

Read more less

This single coil pickup is a passive, ceramic magnet unit, suitable for neck and middle position placement. Features adjustable polepieces for improved accurate individual string response.

Read more less

Neck (covered) single coiled pickup. Match with Wilkinson WVTN bridge pickup fora classic combination has been used for the last 40 years to create all styles of music from Country to Rock, Blues and even Jazz.

Read more less

Since its introduction in 1954, this classic design is the most copied guitar vibrato bridge ever.  The design is so simple and eminently usable it is a challenge to improve on it, but improve it we did!Faithfully reproducing the size and weight of the original, this is a direct retro-fit for the "real thing" but with the added benefit of a push-in vibrato arm (rather than the troublesome original screw-in type).We also staggered the string holes in the sustain block allowing the strings to follow the natural intonation line of the saddles, keeping the strings' "angle of attack" over the saddle's intonation point more consistent, eliminating annoying string "hang-up" giving unrivalled tuning stability.Completing the assembly are the bent steel saddles built from the same gauge steel as the originals to retain the "vintage sparkle" that this bridge has become famous for.

Read more less

A solid steel sustain block creates the ultimate WVPC bridge.

Read more less

While the original spec for Humbucker bobbins was black, a shortage of these items on the production line in the 1950s resulted in bobbins being sourced in virgin material (ivory coloured plastic), hence when guitarists started to remove their brass covers, they discovered that some guitars contained what have become known as Zebra pickups. Some people believe these are the best sounding double coils ever. Trev just think they look great, and by using the same windings as the WVC pickup, they are as authentic sounding as anything currently available.

Read more less

While the original spec for Humbucker bobbins was black, a shortage of these items on the production line in the 1950s resulted in bobbins being sourced in virgin material (ivory coloured plastic), hence when guitarists started to remove their brass covers, they discovered that some guitars contained what have become known as Zebra pickups. Some people believe these are the best sounding double coil pickups ever. Trev just think they look great, and by using the same windings as the WVC pickup, they are as authentic sounding as anything currently available.

Read more less

Currently MIDI wireless has to work together with computers, but with the Xvive MD1 over Bluetooth® you can connect all your MIDI devices without the need for any computer! The Xvive XMD1 is the first Bluetooth® MIDI adapter that can perform as both a 'peripheral' or 'central' device, allowing fast, low-latency, and stable point-to-point wireless connections between any two devices. Featuring Bluetooth® 5 technology for the interconnection of any 5-pin DIN-socket MIDI device, the MD1 Bluetooth® MIDI adapter does not require special software, or extra hardware for secured connections, with twice the speed and with a range of up to 20 meters without obstruction.  Easy to operate and with an instant set up, the MD1 Bluetooth® MIDI, features automatic master/slave switching and default pairing memory, whilst performing with ground breaking latency reduction as low as 3ms, with smart algorithmic, transmission optimisation.    Not just an alternative to trailing leads in the studio and on stage, the MD1 Bluetooth® MIDI adapter benefits a host of applications including the pairing of your iOS device or Mac with one XVIVE MIDI Master using smart auto switch mode. POINT TO POINT MIDI CONNECTIVITYSimply replace your MIDI cables.Rearrange your studio and enjoy the freedom of MIDI.ULTRA LOW LATENCYGo pro with ground-breaking latency reduction as low as 3ms.Smart algorithmic transmission optimization.BLUETOOTH® 5: GO FASTER, GO FURTHERTrusted technology for live and on stage.Secure connection with twice the speed and four times the range. AUTOMATIC PAIRINGSetup instantly. Operate easily.Automatic master/slave switch and default pairing memory.MIDI CLOCK AND SysSExSync your drum machines, step sequencers and arpeggiators.Transmit all MIDI messages over Bluetooth®.NO EXTERNAL POWEREnjoy the fully standalone wireless solution.Supports both 5V and 3.3V via MIDI OUT DIN.VERSATILE APPLICATIONConnect with even the rarest instruments.45 degree bridge cable design for vertical DIN connector setup.MIDI TO MIDIConnect two standalone MIDI hardware deviceswith two XVIVE MIDI Masters.BLUETOOTH (BLE) TO MIDIPair your Bluetooth® MIDI controller with any standaloneMIDI hardware device using one XVIVE MIDI Master.MACOS/IOS BLE TO MIDIPlay your standalone MIDI hardware and pair it with your iOSdevice or Mac with one XVIVE MIDI Master usingsmart autoswitch mode. AboutWindows/Android.GUITAR MIDI CONTROLLER TO DIGITAL GUITAR AMPGuitar MIDI pedal wireless control remote guitar AMPMULTIPLE SETS CONNECTIONSMultiple set of equipment interworking connection,synchronous data transmission COMPATIBLE DEVICES   iPhone/iPad/iPod Touch/Android/Computer COMPATIBLE OS   iOS 8 or later. Yosemite, Windows 10 or later TECHNOLOGY   Bluetooth® 5, Compatible with Bluetooth 4.0 or later LATENCY   As low as 3 ms (test with two MD1) RANGE   20 meters without obstruction CONNECTORS   MIDI IN/OUT (5pin-DIN)  

Read more less

If you want to use the PX system with up to five people simultaneously, and you’re able to work with the same three signals from the soundboard or other audio source/s, you can upgrade your system with a PX-H 5-channel hub, and up to four additional PX-A mixer/preamps and EC25 Cat 5 cables. All connected PX units are powered by one 9V/2A power supply connected to a PX-B that feeds audio and power to the hub! System includes:• One Cat 5 input• Five Cat 5 outputs• Includes a 19” 1U rackmount kit

Read more less

Xvive’s best-selling, problem-solving U4 In-Ear Monitor Wireless System is now available as the XU4T9, a complete, self-contained package featuring everything required for extreme, high quality audio monitoring at home, in the studio or in a live stage environment.  This superb compact and highly portable wireless system includes the popular Xvive U4 6 channel Transmitter and Receiver, Xvive’s high-quality T9 In-Ear monitors with balanced drivers, deluxe CU Series travel cases and a host of accessories that account for a no-fuss, plug-in-and play system. Both the XU4’s transmitter and receiver are built to last, with a tough, robust plastic/metal construction. The receiver itself, with a sturdy metal belt clip, is unobtrusive with fiddle-free easily accessible Headphone Volume control and lockable Channel Select control.  The XU4T9 system is multi-functional, with the transmitter and receiver featuring 6 selectable channels for creating up to 6 individual discrete mixes or, by selecting the same channel as the transmitter, the same monitor signal can be sent to multiple receivers simultaneously.  With a balanced XLR input, the XU4’s transmitter also features Power/Mute, Aux/Line switches and status LEDs for Power, Channel Select and Battery life.    Charging for both units is via a standard USB port, from which the transmitter and receiver will each deliver up to 5 hours playing time, with a line of sight range of 90ft (27.5m) and, with a signal to noise ratio at 107 decibels, provides exceptionally clear and detailed reproduction audio at any volume within the operating 2.4Ghz frequency range, with a latency response of less than 5 milliseconds.  Accessories include, a male XLR to ¼ in jack adaptor, Micro-USB charging jack, USB ‘Y’ lead for charging the transmitter and receiver simultaneously, a cleaning tool and a large selection of silicone tipped ear-piece buds for the T9 In-Ear monitors to suit different ear canal sizes, offering individual comfort and a secure fit.  Available as a separate item the Xvive T9 In-Ear monitors, hand-made in the USA by IEM engineers, deliver pro-level audio quality with the finest details and, like the XU4T9 system, include a robust, lightweight CU Series hard shell travel case.  U4 Features• In-ear monitor wireless system for musicians.• 6 switchable channels allow parallel use of 6 systems. • Integrated rechargeable lithium battery transmitter (860 mAh) and receiver (1200mAh) for long battery life of more than 5 hours.• Y-USB Micro-USB charging cable for simultaneous charging of transmitter and receiver.• Range up to 90ft (without obstacles).• Less than 5 ms latency.• Frequency range  20 - 20,000 Hz.• 2.4 GHz ISM Band for world-wide use.• 24 bit / 48 kHz.• 107dB dynamic range & Signal-To-Noise Ratio.• Runs up to 5 hours per battery charge (2.5hr charge time for a full charge)• On/Off switch.• Channel switch.• Status LED show selected channel and indicates battery life.• Durable ABS and metal housing.• Micro-USB charging jack.• Line and Aux input mode on transmitter.• Receiver 1/8" output supports 6-600Ω Impedance headphones.• Includes U4 transmitter and receiver, T9 In-Ear Monitors, CU4 Travel Case and XLR Male to 1/4" TS Male Adapter. T9 Features• Dual balanced-armature drivers• Hand-assembled• Sound-isolating earphones• Both silicone and memory-foam ear tips included in three sizes• 3.5 mm earphone jack, compatible with all systems• Carrying case and cleaning tool included• Durable, replaceable cables• Custom-designed, unified crossover ensures that each driver is only sent frequencies they were designed to reproduce

Read more less

The Xvive U3T is a wireless transmitter designed for use with the U3 Microphone Wireless System, and can be used as a replacement or backup unit. Although only one transmitter can be used with a U3R receiver at a time, the receiver can toggle between two transmitter sources by changing from the channel of one to the channel of the other. SpecificationsWIRELESS TYPE: 2.4 GHz ISM worldwide open bandBIT DEPTH / SAMPLE RATE: 24-bit / 48 kHzSWITCHABLE CHANNELS: 6SIMULTANEOUS CHANNELS: 6MODE Input: Mic / Line FREQUENCY RESPONSE: 20 Hz – 20 kHz (-3dB)DYNAMIC RANGE: 110 dB (-3 dB)MICROPHONE COMPATIBILITY: Dynamic and battery-powered condenser microphonesSIGNAL-TO-NOISE RATIO: 110 dB TOTAL HARMONIC DISTORTION: 0.2%LATENCY: 5 msOPERATING RANGE: 27.5 m / 90 ft (line-of-sight)POWER N/A MODE Input: Mic / LineMUTE: YesCONNECTOR: XLR (female) DIMENSIONS: 31 x 29 x 98 mm / 3.9" x 1.2" x 1.1"WEIGHT: 93 g / 3.3 oz

Read more less

As a musician and/or singer, whether you’re performing live, rehearsing with a band or recording in a studio, you need to hear both yourself and the other musicians. But just as importantly, you need to have control over what you hear. Everyone hears differently from their own perspective, so everyone needs to have control over their own mix.With the PX system, control of that balance is always within reach, and always adjusted perfectly to your liking! System includes:• One PX-A mixer/headphone amplifier• One PX-B snake• One Cat 5 25-foot cable (7.62 meters）• Three balanced XLR to unbalanced ¼” TS adapters

Read more less

A headphone preamp that allows you to control the overall volume of your in-ear monitors. This helps you manage the volume level, ensuring that you hear what you need to hear for optimum performance, while also giving you the ability to lower the volume if and when the levels are too high for comfort. System includes:• One PX-B 3-channel snake, with three XLR inputs, one Cat 5 output, and a5V/2A power input•Three balanced XLR to unbalanced ¼” TS adapters

Read more less

The Xvive Portable Mixer / Headphone Amplifier gives musicians and singers control of their own monitor mix on the fly, without relying on engineers or other band members. Choose three instruments or microphones, or three submixes of any channels, or a combination.Then adjust the levels as necessary as you perform! System includes:• One PX-A mixer/headphone amplifier

Read more less

Take your performance directly to the audience with the XU7 Saxophone and Trumpet Wireless System! TOP SHELF MIC Sound quality is paramount—and without a good microphone, the U7 would be worthless. That’s why we refused to compromise in our design of the system’s ultra-high-quality supercardioid gooseneck microphone. It’s perfectly voiced for sax, trumpet and trombone—and with a max SPL of 142 dB and a sensitivity of -45 dB, you’ll hear the natural sound of your instrument wherever you go. FREE AS THE WIND Xvive has built its name on wireless, and we understand the importance of reliable performance and top-level fidelity. The U7 system uses the 2.4 GHz band, has 6 channels to ensure you always have options if you encounter interference, and the wireless range is up to 90 feet! CLIP IT ON The U7 set comes with a strong and sturdy clip that attaches the transmitter and gooseneck microphone to the bell of your sax, trumpet or trombone. MIC POSITION The gooseneck microphone is designed to be adjustable, allowing you to position it as desired to get the sound that best captures the tone of your instrument. CONTROL THE WIND Since with a wireless unit you will be moving around more as you perform, sometimes you may want to attach the included foam windscreen or fur windshield to filter out wind noise! WHAT’S IN THE CASE The U7 box includes a Carry Case, Microphone, Transmitter, Receiver, Dual USB-C Charging Cable, Clip, Windscreen, Windshield and Manual. CHARGE IT Charge the transmitter and receiver at the same time using the dual USB-C cable and any 5V 2A USB power supply. Charging for two and a half hours gets you 5 hours of play time; 1.25 hours gets you 2 hours of play time, and 30 min of charging gets you 1 hour. • 2.4 GHz wireless system with a 142 dB SPL supercardioid microphone • High-resolution 24-bit/48 kHz audio, less than 5 ms latency • 20 Hz – 20 kHz frequency response • Dynamic range of 108 dB, signal-to-noise ratio of 108 dB • Up to 5 hours of battery life • 6 wireless channels • Wireless range: up to 90 feet (27 m) • Includes transmitter, receiver, microphone, clip, USB-C cable, foam windscreen and fur windshield, carry case Microphone Specifications Microphone Type: Supercardioid Dimensions: 20 mm x 28 mm x 190 mm Weight: 35g Output Plug: 1/8” balanced male TRS (Tip = +3.3V, Ring = -3.3V, Sleeve = ground) Sensitivity: -45 dB Max. SPL: Wireless System Specifications Tuning Bandwidth: 2400 – 2483.5 MHz Working Range: 90ft (indoors) Frequency Response: 20 Hz – 20 kHz (-3dB) Dynamic Range: 108dB Signal-To-Noise Ratio: 108dB RF Sensitivity: -88dBm Total Harmonic Distortion: 0.2% RF Output Power: 10 mW E.I.R.P. max Operating Temperature Range: 0°C to 45°C Channel Count: 6 Charging Voltage/Current: 5V / 2A Bit Depth / Sample Rate: 24-bit / 48 kHz Latency: less than 5 ms Transmitter Specifications Dimensions: 40 mm x 29 mm x 50 mm Weight: 35g Audio Input Connector: 1/8” balanced TRS female Maximum Input Level: 3.7 Vp-p Phantom Power: ± 3.3V USB Type: Type-C Antenna Impedance:50 Ω Antenna Type: 1/4 wave sleeve dipole, non-removable Number of Antennas: 1 Receiver Specifications Dimensions: 31 mm x 29 mm x 98 mm Weight: 92 g Output Imedance: 470 Ω (1 kHz) Audio Output Connector: XLR balanced male Maximum Output Level: 3.6 Vp-p USB Type: Type-C Antenna Impedance: 50 Ω Antenna Type: 1/4 wave sleeve dipole, non-removable Number of Antennas: 2

Read more less

Protect your Xvive wireless system with an ultra-light, extra-hard carry case! Shockproof, Dustproof and Water Resistant. • Hard carry case for the U2 Guitar Wireless System• Three-layer EVA hardshell case• High-density oxford cloth exterior• Scratch-resistant, tear-resistant and waterproof• Custom foam insert designed for the U2 system• Includes interior pouch for USB charging cable SAFE AND SECUREXvive CU series carry cases are made of three-layer, extra-hard EVA, covered with an exterior of high-density oxford cloth. Wherever you go, your wireless system will be protected from drops, scratches, bumps and splashes!Inside the case, the custom foam inserts are designed to fit Xvive wireless systems perfectly, so your wireless units won’t rattle around during transport. ABLE TO CARRY CABLEXvive CU series cases all feature an interior zipper-sealed accessory compartment that is ideal for storing your USB charging cable.

Read more less

Protect your Xvive wireless system with an ultra-light, extra-hard carry case! Shockproof, Dustproof and Water Resistant. • Hard carry case for the U3 and U3C Microphone Wireless System• Three-layer EVA hardshell case• High-density oxford cloth exterior• Scratch-resistant, tear-resistant and waterproof• Custom foam insert designed for the U3/U3C system• Includes interior pouch for USB charging cable SAFE AND SECUREXvive CU series carry cases are made of three-layer, extra-hard EVA, covered with an exterior of high-density oxford cloth. Wherever you go, your wireless system will be protected from drops, scratches, bumps and splashes!Inside the case, the custom foam inserts are designed to fit Xvive wireless systems perfectly, so your wireless units won’t rattle around during transport. ABLE TO CARRY CABLEXvive CU series cases all feature an interior zipper-sealed accessory compartment that is ideal for storing your USB charging cable.

Read more less

Protect your Xvive wireless system with an ultra-light, extra-hard carry case! Shockproof, Dustproof and Water Resistant. • Hard carry case for the U4 In-Ear Monitor Wireless System• Three-layer EVA hardshell case• High-density oxford cloth exterior• Scratch-resistant, tear-resistant and waterproof• Custom foam insert designed for the U4 system• Includes interior pouch for USB charging cable SAFE AND SECUREXvive CU series carry cases are made of three-layer, extra-hard EVA, covered with an exterior of high-density oxford cloth. Wherever you go, your wireless system will be protected from drops, scratches, bumps and splashes!Inside the case, the custom foam inserts are designed to fit Xvive wireless systems perfectly, so your wireless units won’t rattle around during transport. ABLE TO CARRY CABLEXvive CU series cases all feature an interior zipper-sealed accessory compartment that is ideal for storing your USB charging cable.

Read more less

Protect your Xvive wireless system with an ultra-light, extra-hard carry case! Shockproof, Dustproof and Water Resistant. • Hard carry case for the U4R4 In-Ear Monitor Wireless System (with four receivers)• Three-layer EVA hardshell case• High-density oxford cloth exterior• Scratch-resistant, tear-resistant and waterproof• Custom foam insert designed for the U4R4 system• Includes interior pouch for USB charging cable SAFE AND SECUREXvive CU series carry cases are made of three-layer, extra-hard EVA, covered with an exterior of high-density oxford cloth. Wherever you go, your wireless system will be protected from drops, scratches, bumps and splashes!Inside the case, the custom foam inserts are designed to fit Xvive wireless systems perfectly, so your wireless units won’t rattle around during transport. ABLE TO CARRY CABLEXvive CU series cases all feature an interior zipper-sealed accessory compartment that is ideal for storing your USB charging cable.

Read more less

Make a more intimate connection with your audience. Go wireless, get off the stage, and take the music directly to them! • 2.4 GHz wireless system with a 142 dB SPL supercardioid microphone•High-resolution 24-bit/48 kHz audio, less than 5 ms latency•20 Hz – 20 kHz frequency response•Dynamic range of 108 dB, signal-to-noise ratio of 108 dB•Up to 5 hours of battery life•6 wireless channels•Wireless range: up to 90 feet (27 m)•Includes transmitter, receiver, microphone, clip, USB-C cable, foam windscreen and fur windshield, carry case TOP-SHELF MICSound quality is paramount—and without a good microphone, the U9 would be worthless. That’s why we refused to compromise in our design of the system’s ultra-high-quality supercardioid gooseneck microphone. It’s perfectly voiced for violin and viola—and with a max SPL of 142 dB and a sensitivity of -45 dB, you’ll hear the natural sound of your instrument wherever you go. STRINGS WITH NO CABLESXvive has built its name on wireless, and we understand the importance of reliable performance and top-level fidelity. The U9 system uses the 2.4 GHz band, has 6 channels to ensure you always have options if you encounter interference, and the wireless range is up to 90 feet! CLIP IT ONThe U9 set comes with a strong and sturdy clip that attaches the transmitter and gooseneck microphone to the body of your violin or viola. It will fit on on instrument bodies that are between 30 mm and 40 mm thick (1.18” – 1.57”) MIC POSITIONThe gooseneck microphoned is designed to be adjustable, allowing you to position it as desired to get the sound that best captures the tone of your instrument. CONTROL THE WINDSince with a wireless unit you will be moving around more as you perform, sometimes you may want to attach the included windscreen or windshield to filter out wind noise! WHAT’S IN THE CASEThe U9 hardshell carry case includes: Microphone, Transmitter, Receiver, Dual USB-C Charging Cable, Clip, Windscreen, Windshield and Manual. CHARGE ITCharge the transmitter and receiver at the same time using the dual USB-C cable and any 5V 2A USB power supply. Charging for two and a half hours gets you 5 hours of play time; 1.25 hours gets you 2 hours of play time, and 30 min of charging gets you 1 hour. Microphone SpecificationsType: SupercardioidDimensions: 20 mm x 28 mm x 190 mmWeight: 35gOutput: 1/8” balanced male TRS (Tip = +3.3V, Ring = -3.3V, Sleeve = ground)Sensitivity: -45 dBMAX. SPL: 142dB Wireless System SpecificationsTuning Bandwidth: 2400 – 2483.5 MHzWorking Range: 90ft (indoors)Frequency Response: 20 Hz – 20 kHz (-3dB)Dynamic Range: 108dBSignal-To-Noise Ratio: 108dBRF Sensitivity: -88dBmTotal Harmonic Distortion: 0.2%RF Output Power: 10 mW E.I.R.P. maxOperating Temperature Range: 0°C to 45°CChannel Count: 6Charging Voltage / Current: 5V / 2ABit Depth / Sample Rate: 24-bit / 48 kHzLatency: Less than 5ms Transmitter SpecificationsDimensions: 40 mm x 29 mm x 50 mmWeight: 35gAudio Input Connector: 1/8” balanced TRS femaleMximum Input Level: 3.7 Vp-pPhantom Power: ± 3.3VUSB Type: Type-CAntenna Impedance: 50 ΩAntenna Type: 1/4 wave sleeve dipole, non-removableNumber of Antennas: 1 Receiver SpecificationsDimensions: 31 mm x 29 mm x 98 mmWeight: 92gOutput Impedance: 470 Ω (1 kHz)Output Connector: XLR balanced maleMaximum Output Level: 3.6 Vp-pUSB Type: Type-CAntenna Impedance: 50 ΩAntenna Type: 1/4 wave sleeve dipole, non-removableNumber of Antennas: 2

Read more less

Take your performance to the next level with the U8 Acoustic Guitar Wireless System. Going wireless liberates you to interact directly with your audience, and with the U8’s premium-quality microphone, you will do so with incredible sound! • 2.4 GHz wireless system with a 142 dB SPL supercardioid microphone•High-resolution 24-bit/48 kHz audio, less than 5 ms latency•20 Hz – 20 kHz frequency response•Dynamic range of 108 dB, signal-to-noise ratio of 108 dB•Up to 5 hours of battery life•6 wireless channels•Wireless range: up to 90 feet (27 m)•Includes transmitter, receiver, microphone, clip, USB-C cable, foam windscreen and fur windshield, carry case TOP SHELF MICSound quality is paramount—and without a good microphone, the U8 would be worthless. That’s why we refused to compromise in our design of the system’s ultra-high-quality supercardioid gooseneck microphone. It’s perfectly voiced for acoustic and classical guitars—and with a max SPL of 142 dB and a sensitivity of -45 dB, you’ll hear the natural sound of your instrument wherever you go. STRUM AND STROLLXvive has built its name on wireless, and we understand the importance of reliable performance and top-level fidelity. The U8 system uses the 2.4 GHz band, has 6 channels to ensure you always have options if you encounter interference, and the wireless range is up to 90 feet! CLIP IT ONThe U8 set comes with a strong and sturdy clip that attaches the transmitter and gooseneck microphone to the body of your acoustic or classical guitar. It will fit on instrument bodies that are between 74 mm and 105 mm thick (2.9”– 4.13”). MIC POSITIONThe gooseneck microphone is designed to be adjustable, allowing you to position it as desired to get the sound that best captures the tone of your instrument. CONTROL THE WINDSince with a wireless unit you will be moving around more as you perform, sometimes you may want to attach the included windscreen or windshield to filter out wind noise! WHAT’S IN THE CASEThe U8 set includes a Carry Case, Microphone, Transmitter, Receiver, Dual USB-C Charging Cable, Clip, Windscreen, Windshield and Manual. CHARGE ITCharge the transmitter and receiver at the same time using the dual USB-C cable and any 5V 2A USB power supply. Charging for two and a half hours gets you 5 hours of play time; 1.25 hours gets you 2 hours of play time, and 30 min of charging gets you 1 hour. Microphone SpecificationsType: SupercardioidDimensions: 20 mm x 28 mm x 190 mmWeight: 35gOutput: 1/8” balanced male TRS (Tip = +3.3V, Ring = -3.3V, Sleeve = ground)Sensitivity: -45 dBMAX. SPL: 142 dB Wireless System SpecificationsTuning Bandwidth: 2400 – 2483.5 MHzWorking Range: 90ft (indoors)Audio Frequency Range: 20 Hz – 20 kHz (-3dB)Dynamic Range: 108dBSignal-To-Noise Ratio: 108dBRF Sensitivity: -88 dBmTotal Harmonic Distortion: 0.2%RF Output Power: 10 mW E.I.R.P. maxOperating temerature Range: 0°C to 45°CChannel Count: 6Charging Voltage / Current: 5V / 2ABit Depth / Sample Rate: 24-bit / 48 kHzLatency: Less than 5 ms Transmitter SpecificationsDimensions: 40 mm x 29 mm x 50 mmWeight: 35gAudio Input Connector: 1/8” balanced TRS femaleMaximum Input Level: 3.7 Vp-pPhantom Power: ± 3.3VUSB Type: Type-CAntenna Impedance: 50 ΩAntenna Type: 1/4 wave sleeve dipole, non-removableNumber of Antennas: 1 Receiver SpecificationsDimensions: 31 mm x 29 mm x 98 mmWeight: 92gOutput Impedance: 470 Ω (1 kHz)Audio Output Connector: XLR balanced maleMaximum Output Level: 3.6 Vp-pUSB Type: Type-CAntenna Impedance: 50 ΩAntenna Type: 1/4 wave sleeve dipole, non-removableNumber of Antennas: 2

Read more less

TRANSMITTER AND RECEIVER IN ONE – Plug & PlayFeaturing a rechargeable lithium battery with life of 4/5 hours at full charge, the XU2 Wireless Guitar System from Xvive is the most compact and easy way of freeing yourself from the usual tangle of cables that is every musicians bane. Comprising of two simple and small 1/4 jack connectors that act as transmitter and receiver, the XU2 is ideal for stage, home and studio use and can also connect via Bluetooth to your favourite devices, using 24bit resolution to capture every detail in realtime – uncompressed, natural, clean tone with no delay – 2.4GHz at a range of up to 70ft/25m.

Read more less

TRANSMITTER AND RECEIVER IN ONE – Plug & PlayFeaturing a rechargeable lithium battery with life of 4/5 hours at full charge, the XU2 Wireless Guitar System from Xvive is the most compact and easy way of freeing yourself from the usual tangle of cables that is every musicians bane. Comprising of two simple and small 1/4 jack connectors that act as transmitter and receiver, the XU2 is ideal for stage, home and studio use and can also connect via Bluetooth to your favourite devices, using 24bit resolution to capture every detail in realtime – uncompressed, natural, clean tone with no delay – 2.4GHz at a range of up to 70ft/25m.

Read more less

TRANSMITTER AND RECEIVER IN ONE – Plug & PlayFeaturing a rechargeable lithium battery with life of 4/5 hours at full charge, the XU2 Wireless Guitar System from Xvive is the most compact and easy way of freeing yourself from the usual tangle of cables that is every musicians bane. Comprising of two simple and small 1/4 jack connectors that act as transmitter and receiver, the XU2 is ideal for stage, home and studio use and can also connect via Bluetooth to your favourite devices, using 24bit resolution to capture every detail in realtime – uncompressed, natural, clean tone with no delay – 2.4GHz at a range of up to 70ft/25m.

Read more less

TRANSMITTER AND RECEIVER IN ONE – Plug & PlayFeaturing a rechargeable lithium battery with life of 4/5 hours at full charge, the XU2 Wireless Guitar System from Xvive is the most compact and easy way of freeing yourself from the usual tangle of cables that is every musicians bane. Comprising of two simple and small 1/4 jack connectors that act as transmitter and receiver, the XU2 is ideal for stage, home and studio use and can also connect via Bluetooth to your favourite devices, using 24bit resolution to capture every detail in realtime – uncompressed, natural, clean tone with no delay – 2.4GHz at a range of up to 70ft/25m.

Read more less